Good to know

Our Best Picks

Popular Accessories

PVHEGonG High Efficiency GonG Female

No products with the selected options in stock
PVHEGonG18F
PVHEGonG Female

$24.97

PVHEGonG   P lanet V ape H igh E fficiency GonG Female Take your vapor water conditioning with your Solo to New Heights with these custom Glass on Glass adapters utilizing our Micro Channel Technology to improve airflow by 30% while still maintaining thick, dense...

Choose your options

PVHEGonG   PlanetVape High Efficiency GonG FemalePVHES Female GonG Authorized Distributor Warranty Approved

Take your vapor water conditioning with your Solo to New Heights with these custom Glass on Glass adapters utilizing our Micro Channel Technology to improve airflow by 30% while still maintaining thick, dense vapor clouds. Extract more from your flowers in less time, improving on efficiency by more evenly and thoroughly vaporizing your flowers.

This version of the PVHEGonG has a Female joint instead of a male for direct use with oil rigs and bubblers that have a male joint on them.

 

** NOT COMPATIBLE WITH SOLO 2 **

 

PVHEGonG Female Features:

  • Same Bowl Size As a Standard Stem
  • Micro Channel Technology
  • Multiple Air Entry Points
  • Female Joint

 

PVHEGonG Female Shorty:

  • 30% Smaller Bowl Size
  • Micro Channel Technology
  • Multiple Air Entry Points
  • Overall Adapter Length Remains Unchanged From Non Shorty
  • Female Joint

 

Turbo Option:

  • Large Single Bore With a Glass Rim To Hold The Required Screen
  • Micro Channel Technology
  • Multiple Air Entry Points
  • Female Joint

 

Includes:

  • (1) x PVHEGonG Female of Your Choice
  • (1) x Custom Solo Stainless Steel Screen

 

Instructions:

  • Grind your flowers to a fine consistency, recommended to use our Volcano Grinder
  • Fill the bowl on your PVHEGonG all the way and very very lightly pack a bit
  • Holding your Solo upside down, insert the PVHEGonG Stem all the way in and then insert the GonG into your water tool
  • Turn your Solo on and heat to your desired temperature (minimum 5 recommended to start) with PVHEGonG inserted during warm up
  • Once Solo reaches your selected temperature wait an extra 60 seconds to heat soak your biomass and PVHEGonG
  • Take a nice long slow inhalation
  • Wait 30 seconds between hits to allow your Solo to stabilize
  • Due to much less air flow resistance of the PVHEGonG, resist the urge to inhale too fast, overwhelming the Solo's heater
  • When lifting the PVHEGonG to clear your water tool, always keep the PVHEGonG in the Solo to retain heat
  • You can raise the temperature for the last few hits to get the full spectrum from your flowers
  • Bowl is spent when there is no more vapor production
  • Always empty spent bowl while it is still at its hottest, a cool bowl is much harder to empty cleanly

 

Look For The Authorized Logo!
Always look for the Authorized Logo to ensure you are buying Genuine PlanetVape accessories and water tools.

Disclaimer: PlanetVape is not responsible for any damage or personal injury caused by or from using our products. Glass is breakable and sharp, please use accordingly.

Wow this is great! Quality glass, great instructions and packaging! I get better airflow and this works perfectly with my bubbler. Planet Vape is a great company. They ship FAST to the US. I will be back for more. Thanks :)

Envío rapido y pieza de calidad.Viene con una bolsa de chips de regalo!

Just received from PV the PVHEGonG Female 18MM w/o-ring attached, and also the PVHES Bent Turbo. Instructions were included for o-ring installation (which I do not agree with on method), it states: "Just remove the top screw on cap from the Solo, center the O-ring over the heater port and screw the Solo top cap back on while keeping the O-ring centered. Do not over tighten." The fact is, if you attempt this method, you will likely not be able (as I was not) to center the O-ring because as you turn/tighten the cap, the O-ring will shift around. BUT...if you 1) put the stem through the removed cap, and 2) install the O-ring onto to the stem bowl end, then 3) install the stem bowl all the way into the heater bowl, then 4) screw on the cap...the O-ring will be in place AND stay in place when the stem is removed for refill or replacement. The O-ring holds the stems/adapters VERY firmly in place and eliminates any air intrusion (which IMO defeats the extra air features of the PVHES & Turbo design).
My impression of the draw for the PVHES Bent Turbo w/out O-ring is good: The draw is much smoother and more comfortable than the OEM stem (but NOT w/the O-ring in place). The PVHEGonG allows for smooth albeit slow draw with bubbler (but NOT as good w/O-ring in place). I would liken the draw of the bent turbo w/out O-ring with my Ed's wood stem (my fav), and that's good enough for me.

Customers also bought

Accesories

Related products